Your Trusted Source for Decorative Concrete Mixes in Ohio

At BonTon Supply, we’re passionate about decorative concrete. We believe it has the power to transform ordinary spaces into stunning works of art. That’s why we’re dedicated to providing Ohio tradesmen and contractors with the highest quality decorative concrete products and expert guidance to bring their visions to life.

Have a custom project? Get a Quote >

Fiberglass Lath That Will Not Rust Behind a Vertical Overlay

Lath is the layer nobody sees and everybody blames. When a vertical overlay lets go two winters later, the failure usually traces back to what was reinforcing it and whether that material was still intact.

Why Lath Enters the Conversation at All

A bonding agent works when the substrate is sound concrete, block, or brick and the surface has been properly prepared. On those jobs, chemical adhesion carries the overlay, and our page on bonding agents covers where that line sits.

Lath enters when it cannot. Framed walls, sheathing, foam, questionable substrates, and assemblies with real thickness all need mechanical reinforcement rather than a bond line alone.

The decision point is simple to state and easy to get wrong. If the overlay is relying on a bond to a sound substrate, prime it. If it is not, reinforce it.

What Corrosion Does to a Metal Lath Assembly

Expanded metal and wire lath are the traditional answer, and on interior work in a dry building they perform.

The problem shows up where moisture does. Metal lath in an assembly that takes water begins to corrode, and corroding steel expands. That expansion works against the cementitious material surrounding it, which is what produces staining, cracking, and eventual spalling in the finished surface.

Ohio exterior work supplies the moisture. So do pool surrounds, outdoor fire features, exterior kitchens, and any wall that takes wind driven rain. On those assemblies the reinforcement material is a durability decision rather than a preference.

Vertical SpiderLath is fiberglass. It does not corrode, which removes that failure mode from the assembly entirely.

Self Furring, and Why the Gap Matters

Reinforcement only reinforces if material gets behind it. Lath pressed flat against a substrate sits in the surface of the scratch coat rather than inside it, which leaves a mesh sitting on top of the material instead of embedded in it.

The vertical SpiderLath ships with self furring strips that hold the mesh roughly a quarter inch off the substrate. That gap is where the scratch coat keys in behind the mesh and locks it into the section.

ASTM C1063 is the standard covering installation of lathing and furring for cement based plaster work, and it addresses lapping, attachment spacing, and furring across lath types. The specification is published by ASTM. Requirements vary by assembly and by jurisdiction, so confirm what applies with the project designer or building official.

The Horizontal Version Is a Different Product

Floors and countertops need reinforcement without the standoff. Material is being placed on top of the mesh under gravity rather than pushed onto a wall, so the furring strips that help on a vertical surface get in the way on a horizontal one.

Horizontal SpiderLath ships without strips for exactly that reason. It reinforces flooring, overlays, countertops, concrete carving, and other cementitious applications where the mesh lies flat in the section.

Concrete countertop work is where this shows up most often. A countertop overlay is thin, spans unsupported area, and gets loaded, which is a combination that rewards reinforcement. Our page on smooth interior overlay work covers the material side of countertop and floor applications.

Cutting, Handling, and Crew Time

The practical differences show up on the first day of a job rather than in the third winter.

Fiberglass lath cuts with a utility knife. Metal lath needs snips, produces sharp edges, and cuts hands. On a large elevation, that difference compounds across every corner, opening, and transition a crew has to work around.

Weight and handling follow the same pattern. Lighter material means less fatigue and faster placement, and neither shows up on a data sheet while both show up on a labor line.

Matching Lath to the Overlay Going Over It

Reinforcement is one layer in an assembly, and the layer above it should be decided at the same time.

Wall Mix is the polymer and fiber enhanced overlay for vertical work, formulated to hold a profile and stay workable through carving and stamping. Our page on vertical overlay applications covers where it fits on fireplaces, chases, and fire features.

Smooth Coat handles horizontal work and countertops, where a fine aggregate mix carries flatness rather than texture.

Why Ohio Contractors Buy Lath From BonTon Supply

BonTon Supply distributes the Stone Edge line to Ohio contractors and tradesmen, and the staff installed these systems on job sites for over a decade before becoming a distributor. Lath is the part of an order sized wrong most often, usually because the substrate was assessed from a photograph rather than in person. There are no minimum order quantities.

If you are looking at a wall or a countertop and trying to decide whether it needs lath at all, the answer depends on what the overlay is bonding to and how much moisture the assembly will see. The BonTon Supply team can work through the substrate with you and size the reinforcement before anything ships. Contact us to describe the assembly.