Your Trusted Source for Decorative Concrete Mixes in Ohio

At BonTon Supply, we’re passionate about decorative concrete. We believe it has the power to transform ordinary spaces into stunning works of art. That’s why we’re dedicated to providing Ohio tradesmen and contractors with the highest quality decorative concrete products and expert guidance to bring their visions to life.

Have a custom project? Get a Quote >

Concrete Carving Materials for Rock Walls, Columns, and Feature Surfaces

Carving is the technique that separates decorative concrete from resurfacing. The same bag that resurfaces a chimney chase can become a ledgestone wall, a boulder face, or a cut limestone column, and what changes is the hand rather than the material.

Carving Is a Method, Not a Product Category

Stamping presses a manufactured pattern into a surface. Carving cuts a surface that did not exist until someone made it.

The consequence is repetition. A stamp mat repeats every time it lands, and on a large wall that repetition becomes visible. Carved work does not repeat, because no two cuts are identical, which is why carved stone reads as real at close range and stamped stone sometimes does not.

It is also the slowest decorative method and the one most dependent on the person holding the tool. The material does not make the wall convincing. It makes the wall possible.

What the Mix Has to Do

Wall Mix is the professional grade vertical overlay built for this, with a polymer and fiber enhanced formula that provides extended working time for stamping, carving, and texturing while helping the material hold on vertical and overhead surfaces.

Three properties carry carved work specifically.

Body, so the material holds a vertical profile at the thickness carving needs. A mix that slumps takes the carving with it.

Extended working time, because carving a full elevation takes hours rather than minutes. A mix that sets on schedule for a trowel finish sets too fast for a carver.

Flexural strength, so the finished surface moves with the substrate instead of cracking off it. Ohio exterior work makes this non negotiable.

Wall Mix White is the base for pale limestone, sandstone, and bright cut stone work.

Surfaces Worth Carving

Fire features get most of the attention, and our page on fireplace and fire pit surrounds covers that application in full. They are not the only candidates.

Retaining and seat walls. A block retaining wall carved into ledgestone costs a fraction of real stone and carries the same visual weight.

Water features. Pond edges, waterfall faces, and spillways all benefit from carved rock, and this is the application where corrosion in the assembly matters most.

Entry columns and pillars. Carved column faces relate a driveway entrance to the house without stone masonry cost.

Interior feature walls. A carved accent wall in a lower level or a commercial lobby uses the same system without the weather exposure.

Outdoor kitchen bases and bar fronts. Carved faces tie the structure into surrounding hardscape.

What Goes Behind the Carving

Carved work is thicker than a skim coat, which changes what the assembly needs underneath.

On sound, prepared masonry or concrete, Primer 100 improves adhesion between the overlay and the substrate.

On framed walls, foam, questionable substrates, or anywhere the section has real depth, mechanical reinforcement carries the work instead. Vertical SpiderLath holds the mesh roughly a quarter inch off the substrate with self furring strips, creating the space the scratch coat keys into behind it.

Fiberglass rather than metal matters on water features and exterior walls specifically, since corroding metal expands and pushes the finished surface apart. ASTM C1063 covers installation of lathing and furring for cement based plaster work, including lapping and attachment, and is published by ASTM. Requirements vary by assembly and jurisdiction, so confirm what applies with the designer or building official.

Our page on lath selection covers that decision.

Carving, Texture Skins, or Both

Most convincing walls use more than one technique.

Hand carving produces the joints, coursing, and relief that define the stone pattern. Texture skins then add surface character inside the carved shapes faster than hand work would.

Pro Release keeps skins, stamps, and tools from sticking to fresh material and evaporates without leaving residue behind, which keeps the coloring decision separate from the texturing step.

The usual sequence is to carve the structure, texture the faces, then color, and treating those as three passes rather than one produces a better wall than trying to do everything while the material is workable.

Color Is What Finishes the Illusion

A perfectly carved wall in uniform gray reads as carved concrete. Color is what makes it read as stone.

The Liquid Color Pack provides sixteen shades for base, accent, and antique work, carried into the surface by Pro Seal. Antiquing pushed into the carved joints and pulled back off the raised faces is the step that creates depth.

Our page on base, accent, and antique coloring covers the method in detail.

Why Ohio Contractors Buy Carving Materials From BonTon Supply

BonTon Supply distributes the Stone Edge line to Ohio contractors and tradesmen, and the staff carved this work on job sites for more than a decade before becoming a distributor. Carving is the application where quantities get underestimated most often, because a carved section is thicker than crews estimate from a drawing. There are no minimum order quantities.

If you are quoting a carved wall, a water feature, or a set of entry columns, the section thickness and the substrate behind it drive the quantities more than the square footage does. The BonTon Supply team can work through both before you order. Contact us to describe the wall.